Bosch M7.9.7 EURO-3 ECU error codes
P0102 low signal level of the mass air flow sensor
P0103 high signal level of the mass air flow sensor
P0112 low level of the intake air temperature sensor
P0113 high level intake air temperature sensor
P0116 set the CTS. Out of the allowed range.
P0117 Low level of the DTOJ signal
P0118 High level of the DTOJ signal
P0122 Low throttle position sensor signal
P0123 High level of throttle position sensor signal
P0130 malfunction of the oxygen sensor before the neutralizer
P0131 DC to neutralizer, low signal level
R0132 DC to neutralizer, high signal level
P0133 DC to neutralizer, slow response to enrichment/depletion
P0134 DC to neutralizer, signal circuit breakage
P0135 DC to neutralizer, heater fault
P0136 DC after neutralizer, earth fault
P0137 DC after neutralizer, low signal level
P0138 DC after neutralizer, high signal level
P0140 after the DC Converter, the circuit is open
P0141 DC after the neutralizer is faulty
P0171 too poor mix
P0172 too rich a mixture
P0201, P0202, P0203, P0204 Break in the control circuit of the nozzle 1, 2, 3, 4-th cylinder (respectively)
P0261, P0264, P0267, P0270 Short circuit to the mass of the control circuit of the nozzle of the 1,2,3,4-th cylinder (respectively)
P0262, P0265, P0268, P0271 Short circuit to the power supply of the control circuit of the nozzle of the 1,2,3,4-th cylinder (respectively)
P0300 multiple ignition omissions Detected
P0301, P0302, P0303, P0304 ignition omissions Detected in 1 (2, 3, 4) cylinder
P0327 low level of the detonation sensor signal
P0328 high level of the detonation sensor signal
P0335 no signal from the crankshaft position sensor
P0336 crankshaft position Sensor-signal output beyond the permissible limits.
The P0337 crankshaft position Sensor circuit - short to ground
P0338 crankshaft position Sensor-chain break
P0340 camshaft position sensor Malfunction
P0342 camshaft position Sensor-low level
P0343 camshaft position Sensor - high level
P0422 neutralizer Efficiency below the acceptable threshold
P0441 Incorrect air flow through the purge valve
P0443 adsorber purge valve control Failure
P0480 fan relay control Circuit 1: open, short to ground or +12V.
P0481 fan relay 2 control Circuit: open, short to ground or +12V.
P0500 No car speed sensor signal
P0503 speed Sensor-intermittent signal
P0506 Rxx locked, low rpm
P0507 Rxx blocked, high rpm
P0560 the on Board network Voltage is below the system health threshold
P0562 Low voltage on Board network
P0563 Increased voltage of the onboard network
P0601 FLASH checksum Error
P0603 controller external RAM checksum Error
P0604 controller internal RAM checksum Error
P0615 starter control Circuit, breakage
Circuit P0616 starter control circuit short to ground
P0617 starter control Circuit, short to + 12V
P1135 circuit of the oxygen sensor heater to the neutralizer: open, short to ground or +12V.
P1140 Discrepancy between the measured load and the calculated load
P1141 oxygen sensor heater Circuit after the neutralizer: open, short to ground or +12V.
P1386 detonation detection Channel. Internal test error
P1410 adsorber purge valve control Circuit, +12 V short circuit
P1425 adsorber purge valve control Circuit, ground fault
P1426 adsorber purge valve control Circuit, open
P1501 fuel pump relay control Circuit, ground fault
P1502 petrol pump relay control Circuit, +12 V short circuit.
P1509 Overload of the Rxx control circuit
P1513 control Circuit IAC circuit short to ground
P1514 Rxx control Circuit, open or short at +12 V.
P1541 gas pump relay control Circuit, breakage
P1570 Immobilizer - no positive response or circuit break
P1602 loss of power supply to the controller
P1606 rough road Sensor, wrong signal
P1616 rough road Sensor, low signal level
P1617 rough road Sensor, high signal level
P1640 Electrically reprogrammable memory, read - write test error
P1689 error storage memory Failure